Connect 2 cold water pipes and connect them to the water pump. Note: the lower pipe connected to the water pump is water inlet; sinking pump is used in this product.The water pump should be immersed in water for using. Install the hose at the air outlet. Note: gasket is needed, or air leakage might exist. Install the pressure relief valve screw; pressure relief valve screw is installed at the pressure relief hole under the hose. The blow-down valve is installed at the.
Drain outlet of the first air chamber block. Immerse the water pump in water and switch on the power. Connect the container need to be inflated. Screw up the screws of the blow-down valve and pressure relief valve.Switch on the power ant the machine operates. Note: when the machine is operating, the water must operate correspondingly, or the product might be damaged due to overheated, personal harm may even occur. After the inflation is completed, screw of the pressure relief valve should be firstly loosen, then the power is to be switched off, by doing so, high pressure.
Air backlash caused due to sudden failure of power supply would be avoided, which could lengthen lifetime of the product, as well as discharge high pressure air in the machine. The product should be placed at a place that it couldnt be touched by children.
Please do not use it in moist and flammable place. Please do not modify it arbitrarily, disassembling and repair by non-technical personnel is not allowed. Make sure the socket could withstand a current greater than 8A before using it, or the circuit might be burnt, the product might be damaged and the dangers may be caused due to overload of the socket. Please do not touch the head section after the machine was just being used, so as to not be burnt by high temperature. Please do not leave without authorized, or the product might be damaged by increasingly rising pressure, sustained overload motor.
Even halt due to the operation pressure has reached but it is not turned off timely. When it is used for inflating slightly larger container, the cooling water should be changed every 30 minutes, in this way, the. Cylinder temperature could be better controlled.The machine oil should be checked regularly, make sure the oil level is above the upper edge of the red point. Machine oil becomes dark and black, it should be changed in time. 110V High Pressure 30Mpa Air Pump Compressor Pump PCP Electric. We believe the good communication is important for a happy shopping experience. Please do not leave without authorized, or the product might be damaged by increasingly rising pressure, sustained overload motoreven halt due to the operation pressure has reached but it is not turned off timely. When it is used for inflating slightly larger container, the cooling water should be changed every 30 minutes, in this way, the cylinder temperature could be better controlled. If color of machine oil becomes dark and black, it should be changed in time. (46# anti-wear hydraulic oil of the national standard is recommended). We offer you a superior. The followings you should know. Compressed air through the cyclone after the high-speed rotation, driven by inertial centrifugal force in the oil particles and condenser water particles will be thrown to the outer wall, hit the inner wall of the separator shell along the wall after the discharge. Practical each time after filling the oil and water mixture. Able to filter directly more than 5 microns of impurity. Controlling low pressure part of the gas pressure to prevent high pressure parts of the machine failure caused by high pressure gas reflow and damage to low pressure parts. Please add lubricating oil before you start using the machine first. Dont forget to put the lube oil into the compressor before running.
When running, if the machine vibrates violently, please add pad or towel under the. When the compressor working, the cooling system must be working at the same time. The machine must not be working without oil, so you must pay attention to the level of oil. 46 wear resistant hydraulic oil. If the machine vibrates violently, please add pad or towel under the compressor.
The compressor working, the cooling system can be working at the same time. The machine must be working with oil, so you must pay attention to the level of oil. High pressure test leak test pressure. Size: 36 18 37CM/188.8.131.52 INCH. Net Weight: 16.2KG/35.72LBS.Charge pressure: 30MPA (it will automatic shut down when the pressure reach 30MPA). Air flow rate: 50L/MIN(13.2GPM). Working Pressure: 300BAR 30MPA 4500PSI. Working pressure: 300 BAR/ 30MPA/ 4500PSI. Name: High pressure pneumatic pump. Voltage: 110V /50Hz (We could provide different charger plugs for a different country requirements - US plug, UK plug or EU plug by default). Working pressure: 300 BAR/ 30MPA/ 4500 PSI. Product size: 360 180 370 mm/ 14.17 7.09 14.56 inch. Package size: 49 50 32 cm. Filling Time: 10 mins per 1L tank valve quantity. Air volume: 100 (L / min).
Color: As shown in the pictures. Product dimension: 35x18x35cm/13.8x7.1x13.8inch. Power cord length: 1 (M). 1PC × 30Mpa Electric Compressor Pump.2Pcs × Pressure Relief Screw. 2 Bags × Air filter cotton pad. 1 x complete high pressure pump.
We believe that it is our vision and mission to provide innovative products with best service and competitive price to satisfy you. Our goal is to make sure that you can find exactly what you are looking for and make it easy for you to place your orders. Caifornia Warehouse: 18501 Arenth Ave, City of Indus-try, CA 91748. 300 W Airtex Blvd, Suite 200, Houston, TX 77090. 2125 Gateway Blvd, Hebron, KY 41048.
1000 High Street, Perth Amboy, NJ 08861. If you need to return, please check twice to confirm the item not work and contact our customer service representative, let us know the detailed problem and send us some pictures for confirmation. Please make sure that item has NO man-made sabotage.Used items will not be accepted for return. All emails will be responded to within.
Special circumstances will be listed clearly in the listing. Please do check everything carefully after you received the parcel, any the damage except DOA (Dead-On-Arrival) would not be covered if it's your fault.A: The item ships from Rancho Cucamonga, CA, United States. A: Please log on your account. Q: How do I return an item? Please contact our customer service before you return an item. The item "High Pressure Air Pump Electric 300BAR PCP Compressor for Airgun4500Psi 30MPA" is in sale since Tuesday, June 11, 2019.
This item is in the category "Sporting Goods\Outdoor Sports\Air Guns & Slingshots\Accessories". The seller is "rumei-shopping" and is located in Rowland Heights, California. This item can be shipped to United States, Canada, Mexico.